allowable voltage

简明释义

容许电压

英英释义

例句

1.The circuit design must ensure that the maximum allowable voltage 允许电压 does not exceed the rated capacity of the components.

电路设计必须确保最大允许电压 允许电压不超过组件的额定容量。

2.Exceeding the allowable voltage 允许电压 can lead to catastrophic failures in electrical systems.

超出允许电压 允许电压可能导致电气系统的灾难性故障。

3.When designing a power supply, engineers must calculate the allowable voltage 允许电压 to ensure compliance with safety standards.

在设计电源时，工程师必须计算允许电压 允许电压以确保符合安全标准。

4.The manufacturer specifies an allowable voltage 允许电压 range for safe operation of the device.

制造商为设备的安全操作指定了一个允许电压 允许电压范围。

5.In high-voltage applications, it is critical to monitor the allowable voltage 允许电压 to prevent equipment damage.

在高压应用中，监测允许电压 允许电压以防止设备损坏是至关重要的。

作文

Understanding electrical systems requires a solid grasp of various concepts, one of which is the term allowable voltage. This term refers to the maximum voltage that can be applied to an electrical component or system without causing damage or failure. In many engineering applications, knowing the allowable voltage is crucial for ensuring safety and functionality. For instance, in electronic circuits, each component has a specified allowable voltage that must not be exceeded to prevent overheating or breakdown. When designing electrical systems, engineers must carefully consider the allowable voltage of all components involved. This includes resistors, capacitors, inductors, and integrated circuits. Exceeding the allowable voltage can lead to catastrophic failures, including short circuits, fires, or even explosions in extreme cases. Therefore, it is essential to adhere strictly to the specifications provided by manufacturers regarding the allowable voltage.In practical applications, the concept of allowable voltage is often linked to safety standards and regulations. For example, electrical devices used in households and industries must comply with specific voltage ratings to ensure user safety. Electrical codes often dictate the allowable voltage levels for different types of installations, helping to prevent accidents and injuries.Moreover, the allowable voltage can vary depending on environmental conditions. Factors such as temperature, humidity, and altitude can influence the performance of electrical components. Engineers must take these factors into account when determining the allowable voltage for a specific application. For instance, a component rated for a certain voltage at room temperature may not perform the same way at elevated temperatures, thus lowering its allowable voltage.In addition to safety concerns, understanding the allowable voltage is vital for optimizing the performance of electrical systems. Operating components within their specified allowable voltage range ensures they function efficiently and reliably. When components are used beyond their allowable voltage, not only does it risk damage, but it can also lead to decreased performance and increased energy consumption.In conclusion, the term allowable voltage plays a significant role in the field of electrical engineering. It serves as a guideline for safe and efficient operation of electrical components and systems. By understanding and respecting the allowable voltage, engineers can design safer, more reliable, and more efficient electrical systems. The importance of adhering to the allowable voltage cannot be overstated, as it is fundamental to both safety and performance in electrical applications.

理解电气系统需要扎实掌握各种概念，其中一个就是“允许电压”这个术语。该术语指的是可以施加到电气组件或系统上的最大电压，而不会导致损坏或故障。在许多工程应用中，了解允许电压对于确保安全和功能至关重要。例如，在电子电路中，每个组件都有一个指定的允许电压，不得超过该电压，以防止过热或故障。在设计电气系统时，工程师必须仔细考虑所有相关组件的允许电压。这包括电阻器、电容器、电感器和集成电路。超过允许电压可能导致灾难性故障，包括短路、火灾，甚至在极端情况下发生爆炸。因此，严格遵守制造商提供的关于允许电压的规格是必不可少的。在实际应用中，允许电压的概念通常与安全标准和法规有关。例如，家庭和工业中使用的电气设备必须符合特定的电压等级，以确保用户安全。电气规范通常规定不同类型安装的允许电压水平，帮助防止事故和伤害。此外，允许电压可能会因环境条件而异。温度、湿度和海拔等因素会影响电气组件的性能。工程师在确定特定应用的允许电压时，必须考虑这些因素。例如，在室温下额定为某一电压的组件，在高温下可能无法以相同的方式工作，从而降低其允许电压。除了安全问题，理解允许电压对优化电气系统的性能也至关重要。在规定的允许电压范围内操作组件，确保其高效可靠地运行。当组件超出其允许电压使用时，不仅存在损坏风险，还可能导致性能下降和能耗增加。总之，术语允许电压在电气工程领域中发挥着重要作用。它作为电气组件和系统安全高效运行的指导方针。通过理解和尊重允许电压，工程师可以设计出更安全、更可靠和更高效的电气系统。遵守允许电压的重要性不容小觑，因为它是电气应用中安全和性能的基础。